Skip to main content

IOM Alignment and Measuring Jig (UPDATED)

I need to start to consider how I'll mount the fin and bulb, and get it all straight, so I made a 3D modeled alignment jig:



Ian Dundas in Scottland sent me pictures of his setup. I just bought a laser level too! He does amazing work and has been a great help in this project so far.




There is also another jig featured on page 14 of the winter 2008 Canadian Radio Yacht Association (CRYA) newsletter that features one. It's by Lawire Neish. Read it here.

I took both those designs and made my own version that features sliding cradles for the hull, a fixed waterline sight, proper depth to cradles for the bulb, etc... Most of the parts can be laser cut, and the two end pieces and the base can easily be cut on a tablesaw.

It has fixed waterline sights that are 420mm above the top edges of the bulb sliders in the base. The fore and aft cradles can be slid up and down to adjust the waterline of the hull. You'll see that the overall interior length is 1003mm to accommodate the aft slider thickness. I had to come up with a way to account for rudders that might be flush with the transom. But the total distance between the inside of the aft slider and the inside of the forward board is 1000mm.

The bulb sliders can be slid fore and aft to account for varying bulb diameters and bulb cant. The TOP edge of the bulb sliders are longer than needed, and are 420mm below the waterline, so you have a visual reference for the bottom of the bulb and can adjust as needed. 


Here you can see the bulb sliders. They are identical, and the top edges of them are exactly 420 mm below the waterline sights. You slide them forward or aft to adjust the bulb, and bulb cant, as needed. The top edge of the bulb sliders are extended so that you can look at the bulb from the side and see how close the bottom is getting to that 420mm limit.


Here is the forward cradle slider that the bow fits into.
Here is the aft cradle slider.

Here you can see how the transom is against the aft slider and not against the end board. This is to accommodate rudders that are flush to the end of the transom.


I haven't actually made it yet. Hoping for some initial feedback from people more experienced than I in IOM stuff. But might be able to laser cut it by next week and see if I can get it to work.

UPDATE!

UPDATE: I built it and it worked very well! When used in combination with a cheap laser level, you can get millimeter accuracy. You can also much more easily set up your fin and bulb for mounting.





After the next picture was taken, I received the adapter bolt that fit my tripod and the laser level, and I can now raise the laser to the proper waterline level too. It all works really well. 



Here is a link to my DWG file if you wish to laser cut your own version from 3mm (1/8") Lite Ply. This file only includes the parts that need to be laser cut! You will still need to make, cut, assemble the MDF parts yourself. The parts that are colored as plywood in the pictures above are included, the rest aren't. Good luck! 



Aloha!





Comments

  1. Might I suggest making accommodations in the forward slider for a 10mm (or larger) spacer for boats that have not yet attached the bow bumper.

    ReplyDelete
  2. Not a bad idea, but probably just as easy to use a 10mm spacer that you cut yourself. If you're worried that the boat won't fit, the two sliders each extend 20mm into the middle. The 3D boat that I'm using in this example doesn't have a bow bumper, and it sits easily on the slider. Let me consider this though! Thanks!

    ReplyDelete

Post a Comment

Popular posts from this blog

Riptide RC Sailboat

Well I just hit the R/C Sailboat jackpot! Rod Carr, of Carr Sails in Redmond, WA, and the second ever member of the AMYA, just gifted me a Marblehead "Riptide" hull and many of the parts and templates to finish it! Thank you Rod!

I'm not sure when I'll be able to work on this, but hopefully it will turn into a fantastic vintage Marblehead. The gentleman who started it did a fantastic job. He was a true artist and I will do my best to get as close as I can to his workmanship but it will be a challenge.

Here are some pictures...


He even cast his own bulb and the mold came with the hull! I could probably start making my own fleet of Riptides as he also gave me many of the templates and such. I will only need to pin and epoxy the bulb to the fin and fair it smooth. It will be easy to do.


The frames look and feel like he hand cut them on a scroll saw, but they are very close to perfect. He used thicker plywood than I may have but they are very sturdy. The bow is very squ…

IOM Rig Box (IOM Sail Box) plans

So all the cool IOM kids seem to have nice wooden boxes to store their rigs in. This might be my next quick project then, so that I can pretend to be cool too. :-P

The rig box images that I've seen online are mostly similar, and would work well, but David Jensen from Bellevue, WA, USA (The same guy who designed a fantastic IOM boat stand I posted about earlier) has a really nice design that he shared on RC Groups. Or if that link doesn't work, the go here and search for "IOM sail box" or "IOM rig box".

It holds three sets of rigs for the A, B, and C rigs.


He also has a nifty way to attach his IOM boat stand, with a boat on it, to the rig box. His rig box has wheels attached, so once everything is loaded up he just wheels it to the launch spot. Very nice!



There are other sources online. They show different variations of the same type of sail box.

Here's a nice looking one.

Here's a YouTube video of a really nice one.

Will post more if I actually end…

R/C Sailboat Builds

Here are the other boats I've built in the past few years:


1. A Tippecanoe T37. These are kits available from Tippecanoe Boats in Washington State.








2. A classic, wooden, Star 45. It has been officially measured and is class legal. The Star 45 is a pretty, classy, builders boat that has withstood the test of time.







3. A Salish 475. It's my own variation on the Star 45. It was built from the same laser cut frames as the Star with a number of modifications aft of frame 6. It is an update of the classic look and was an attempt to mimic a modern ocean racing yacht.










I've also built four Pygmy kayaks and many other projects. It's all fun... right?!


Aloha!

Radio controlled sailboats

IOM Sailboat Stand

I made an IOM boat stand!



The plans are from David Jensen in Bellevue, WA, USA. I found the plans through someone else's blog here, and a model sailboat club from Australia here.

It was pretty straightforward to build. My only contribution to the design is that I laser cut the cradle out of 1/8" Lite Ply. I made eight copies, and then epoxy laminated two sets of four each. Turned out really well.



If you wish to laser cut your own set, here is my DWG file. You'll have to have your own laser cutter, or send the job to a laser cutting company like National Balsa. Here are the original plans, and here are the original plans for just the cradle. Thanks to David Jensen!!

Note that in the picture below, my boat is not finished! Yikes.


You can't see it in this image, but there's a small chuck of self-stick foam behind the bulb to protect the bulb. I'll eventually incorporate some Velcro or a strap of some sort to hold the bulb in place so that I can use the carry-han…