Skip to main content

Corbie 5 IOM Construction (cont.)

I've made loads of progress on the Corbie 5 since my last post. Most of it has gone well, but I've had a few not so good things happen too.

I've finished the fin box and installed all the bulkhead work around it. It looks like a lot, but doesn't weigh toooo much. It should keep the fin in place though, and it includes a raked mast step slot, a rudder servo mounting plate, and a winch mounting plate.



These two images show the deck just sitting on top. You can see how much access there is to the winch and rudder servos. Should be OK.



This picture shows the shroud chain plates being epoxied in place. I'm a bit concerned that they won't be strong enough. I'm used to "locking" in the chain plates mechanically by slotting them into nearby frames. This seems to be the way it's done though. Gulp.

I used a good amount of thickened epoxy, so fingers crossed they'll hold.



When I installed the fin though, I noticed that it's not a straight as I had hoped. Ugh. We'll see how she floats later.



Aloha!



Comments

  1. I like the look of what you have done around the mast area. Can you tell me where you get the fin box casing? is it purchased or can you CNC cut it?

    ReplyDelete
  2. Hi Colin,

    I made my own fin box. There is the inside bit that exactly fits the fin, and then there's the outer wooden bit that encases the inside bit. The wooden parts are all laser cut. A CNC machine is probably too course for these small detail bits.

    If interested, contact Mirage Radio Yachts. Jeff Byerley is the owner and he can sell you the DXF file. I promised him I would not share any of it.

    Thanks,

    Steve

    ReplyDelete
    Replies
    1. Hi Steve, Thanks for getting back to me. They certainly look good and wondered if it was a kit. But I will contact Jeff and see if he will sell the files

      Delete

Post a Comment

Popular posts from this blog

IOM Sailboat Stand

I made an IOM boat stand! The plans are from David Jensen in Bellevue, WA, USA. I found the plans through someone else's blog here , and a model sailboat club from Australia here . It was pretty straightforward to build. My only contribution to the design is that I laser cut the cradle out of 1/8" Lite Ply. I made eight copies, and then epoxy laminated two sets of four each. Turned out really well. If you wish to laser cut your own set, here is my DWG file . You'll have to have your own laser cutter, or send the job to a laser cutting company like National Balsa . Here are the original plans , and here are the original plans for just the cradle . Thanks to David Jensen!! Note that in the picture below, my boat is not finished! Yikes. You can't see it in this image, but there's a small chuck of self-stick foam behind the bulb to protect the bulb. I'll eventually incorporate some Velcro or a strap of some sort to hold the bulb in place so

IOM Rig Box (IOM Sail Box) plans

So all the cool IOM kids seem to have nice wooden boxes to store their rigs in. This might be my next quick project then, so that I can pretend to be cool too. :-P The rig box images that I've seen online are mostly similar, and would work well, but David Jensen from Bellevue, WA, USA (The same guy who designed a fantastic IOM boat stand I posted about earlier) has a really nice design that he shared on RC Groups . Or if that link doesn't work, the go here and search for " IOM sail box " or " IOM rig box ". It holds three sets of rigs for the A, B, and C rigs. He also has a nifty way to attach his IOM boat stand, with a boat on it, to the rig box. His rig box has wheels attached, so once everything is loaded up he just wheels it to the launch spot. Very nice! There are other sources online. They show different variations of the same type of sail box. Here's a nice looking one . Here's a YouTube video of a really nice one . Wil

A Wooden "Alternative" IOM RC Sailboat

Being forced to stay home due to the Coronavirus quarantine has had a positive impact on my boat building. I still haven't been able to sail my newly completed Vickers V8 IOM, yet have just planked and glassed a wooden Alternative IOM . It only took me eight days. It usually takes a couple weeks. I haven't been motivated to blog about it, but I started planking on 5 April and finished planking last night. Today I sanded and have fiberglassed the outside. The Alternative by Brad Gibson was a challenge to plank due to its up-swept bow and flared sheer near the bow. It turned out okay, but as any builder will tell you, there are goofs all over. One that I only discovered after sanding is a lighter colored plank on the starboard side. It really showed up after fiberglassing as the epoxy brought it out... GAAAAH! How did that get there? The other goofs I'll let you find, but that one is pretty obvious. Here's how it looks so far: Here you can see that mu

IOM Alignment and Measuring Jig (UPDATED)

I need to start to consider how I'll mount the fin and bulb, and get it all straight, so I made a 3D modeled alignment jig: Ian Dundas in Scottland sent me pictures of his setup. I just bought a laser level too! He does amazing work and has been a great help in this project so far. There is also another jig featured on page 14 of the winter 2008 Canadian Radio Yacht Association (CRYA) newsletter that features one. It's by Lawire Neish. Read it here . I took both those designs and made my own version that features sliding cradles for the hull, a fixed waterline sight, proper depth to cradles for the bulb, etc... Most of the parts can be laser cut, and the two end pieces and the base can easily be cut on a tablesaw. It has fixed waterline sights that are 420mm above the top edges of the bulb sliders in the base. The fore and aft cradles can be slid up and down to adjust the waterline of the hull. You'll see that the overall interior length is 1003mm t