Skip to main content

Finishing, part 1

Here we go... time for the finishing. Gulp... I get stressed out during this phase. Too much of a perfectionist I guess, but then I run out of steam and end up being satisfied with an OK job. Maybe this time I'll carry all the way through!

Tonight, I added a coat of Interlux Primekote 404/414 epoxy filler. It's a two-part epoxy compound that fills all the small scratches and such. I'm only adding it below the waterline as that part will be painted red. The topsides will remain clear, so I can use this product there.

The idea behind the Primekote is that you put on a layer or two, and then sand most of it off the next day with pretty fine grit paper. It should fill the scratches, low spots, etc... When you sand it fine enough, it should leave a smooth, plastic-like surface that will take epoxy paint very well.

Here is how it looks with a coat on. I'm only going to do one coat, and then sand it off. Should be good enough. Yes, you can see brush strokes... it doesn't matter as it's almost all going to be sanded off! The final paint coats will be sprayed later.





More in the next day or two when I sand it off.


Peace!




Labels:

Comments

Post a Comment

Popular posts from this blog

1934 America's Cup Rainbow J-Class RC Drawing

At some point I would very much like to model a vintage America's Cup yacht. The one I've been most interested in lately in the 1964 winner Constellation. But this past week I was sent a 1/16 scale drawing of the 1934 Rainbow. It's a beautiful drawing! Full sized so it's very large. I have been working on making it into a 3D model, but as is true with most hand-drawing lines, none of the lines from one view match up with the lines from the other views. For example, I spent a lot of time tracing the "sections" view so I could make stations. But when I tried to match them up with the plan/deck view or the waterplanes view, none of the lines met. Some came close, but all had to be adjusted. Then, once they are matched to the deck and keel lines, it's obvious that the hull is not fair. I honestly doubt that the hull would be fair if you simply used the station lines as originally drawn either. Back when they made these boats, they put it on the actual bu...
2 comments
Read more

IOM Rig Box (IOM Sail Box) plans

So all the cool IOM kids seem to have nice wooden boxes to store their rigs in. This might be my next quick project then, so that I can pretend to be cool too. :-P The rig box images that I've seen online are mostly similar, and would work well, but David Jensen from Bellevue, WA, USA (The same guy who designed a fantastic IOM boat stand I posted about earlier) has a really nice design that he shared on RC Groups . Or if that link doesn't work, the go here and search for " IOM sail box " or " IOM rig box ". It holds three sets of rigs for the A, B, and C rigs. He also has a nifty way to attach his IOM boat stand, with a boat on it, to the rig box. His rig box has wheels attached, so once everything is loaded up he just wheels it to the launch spot. Very nice! There are other sources online. They show different variations of the same type of sail box. Here's a nice looking one . Here's a YouTube video of a really nice one . Wil...
1 comment
Read more

Made a Mast Crane

Made a mast crane based on one that I have made in the past for my Star 45's. Works well for them, and should work well for a Vintage Marblehead Sun Wind. It's made from brass, with a bar for strength soldered to the top. The idea is that a slot will be cut into the top 2" of the mast, and the crane will be through-bolted. This link is to the original schematic of a mast crane that you can build yourself, courtesy of the Miami Valley Model Yacht Club in Ohio.  Here is my updated version. Click to see the full-sized image and then copy and paste it into Word. It "should" print at just about the correct size, but you may have to adjust the image a bit. Cut it out and spray glue it to some brass sheet. Cut it out on a band-saw and then sand smooth. Be careful when working with tools and metals!! This is what I ended up with for my Sun Wind HF. I decided to reinforce the crane with a length of brass bar soldered to the top edge. Back to deck pl...
Post a Comment
Read more

In the Works: "The Wooden IOM Construction Manual"

This is months away, if it ever actually gets completed, but I thought I'd try to get some input on what should be included in " The Wooden International One Metre Construction Manual " for building... get this... a wooden IOM. I'm over 60 pages so far, but it's good to get other ideas and input. This is the third RC sailboat construction manual I've written, and it's the most accurate. But it's also the one that I have the most anxiety about because I'm still a rookie in the IOM world and others are building such gorgeous boats. Unlike Star 45's and Vintage Marbleheads, which are great but not raced as much, IOM's are still very popular. And everyone has their idea of what's best. My goals though are to: 1) Help grow the class and help people get into what is a very competitive and rules-based class. It's a very tough class to fully understand and to compete in. I'm still learning the racing side of IOM's myself, but ...
6 comments
Read more